Listed below are past stories that appeared on the front page of our web site.
| 02/08/10 |
QSM11-P Allison Transmission Support
and 165 LAT Cooling Package
|
|
| |
Do you have an OEM who installs Allison Transmissions? CPP has just
released a mounting option for the Allison 4700OFS transmission along with
an oversized cooling package for an OEM installed tube & shell cooler. The
transmission support bolts to the standard extended baserails and has a 20"
engine centerline height. The oversized cooling package has a 165 degree
LAT to handle the added heat rejection from the transmission. |
|
|
|
|
|
| 02/02/10 |
CPP SHOWCASES “PACKAGE PROOF” DESIGN FOR TIER 4 |
|
| |
 |
Cummins Power Products, showcased a new QSB6.7 Power Unit ready for Tier 4 Interim low emissions in 2011 at the World of Concrete show, which opened today in Las Vegas. The QSB6.7 unit is believed to be the first Tier 4-capable Power Unit displayed with an integrated air-intake-to-exhaust aftertreatment.
Read the whole press release.
|
|
|
|
|
| 01/25/10 |
QSB4.5-P Now Compatible with Cummins Air Compressor!
|
|
| |
 |
For those of you that are in need of an air compressor on an enclosed QSB4.5 the wait is over. Cummins Power Products has revamped enclosure doors on the QSB4.5 power units to eliminate interference with an engine air compressor option! Now, both EN11151 and EN11225 are compatible with the Cummins air compressor option, CP9539. |
|
|
|
|
| 01/22/10 |
A2300 / A2300T Pedestal Mounting |
|
| |
Does your OEM need an even smaller A2300 Power Unit? Cummins Power Products has just released pedestal mounting for the A2300 and A2300T Tier 4i Power Units. The new mounting reduces the width of the foot print by over seven inches and utilizes the low profile cooling package for a very compact power unit. |
 |
|
|
|
|
| 01/17/10 |
New Lifting Provisions on Enclosures! |
|
| |
 |
Cummins Power Products will now be shipping all enclosed QSB power units with overhead lifting provisions. These brackets have been release into the QSB3.3, QSB4.5 and QSB6.7 enclosure options to ease installation of our enclosed power units. Click on the image to enlarge. |
|
|
|
|
| 11/16/09 |
B3.3T-P Power Unit Released! |
|
| |
Cummins Power Products is pleased to announce the release of the B3.3T Power Unit into production (engine configuration D782009CX03). This Power
Unit provides our customers with a Tier 4i certified engine line-up up to
74hp and will not be required to meet Tier 4 final requirements until 2013.
The Power Unit is available in an open and enclosed configuration. For
additional information, please check out the product
page. |
|
|
|
|
|
| 08/18/09 |
GTA8.3-P Re-Released for Export! |
|
| |
 |
CPP is pleased to announce the re-release of the GTA8.3 Power Unit (engine configuration D553011CX03). This power unit will be available to be sold outside the US to foreign markets and includes an enhancement to the cooling system: the Charge Air cooler has been replaced with a 2P2L cooling system. For additional information, including drawings, please check out the product page. |
|
|
|
|
| 08/04/09 |
GTA8.3SLB Power Unit Released! |
|
| |
CPP is pleased to announce the release of the GTA8.3SLB Power Unit (engine configuration D553012CX03). This power unit conforms to 2008 NSPS Standards with the inclusion of Simple Lean Burn (SLB) technology. For additional information, including drawings, please check out the product page. |
|
|
|
|
|
| 06/26/09 |
New DC Generator Programming for Solar Applications! |
|
| |
 |
Cummins Power Products is proud to announce an enhancement to its DCathlon generator product! The control programming has been adapted to better serve the Solar Energy market by allowing the unit to more intelligently monitor when it needs to charge and when it's okay to return to standby mode. This will equate to a fuel savings by our customers, saving everyone money over time! We are proud of this development and leap in programming technology, and expect to continue to use this to better serve our customers in the alternative energy market! |
|
|
|
|
| 05/08/09 |
Automation Alley Member! |
|
| |
Cummins Power Products is now recognized as a member of Automation Alley, a regional consortium of high tech businesses that drive the growth of Southeast Michigan’s technology business economy. Through a collaborative culture that focuses on workforce and business development initiatives, Automation Alley presents opportunities for business leaders to foster technological innovation and economic growth. The organization’s more than 1,000 members represent the diversity of the region's technology industry leaders, progressive businesses, government entities and educational visionaries, all working together to strengthen the region’s economy.
Cummins Power Products’s involvement with Automation Alley supports its continued vision to enhance the region’s economy and contribute to Southeast Michigan’s business community. Collaboration with this innovative organization is of great importance to CPP’s continued growth in Michigan. |
|
 |
|
|
|
|
| 04/02/09 |
G5.9E Power Unit Released! |
|
| |
|
Cummins Power Products is pleased to announce the release of the G5.9e Power Unit (engine configuration D491015CX02). This power unit conforms to 2008 NSPS Standards with a factory installed AFR and includes a 3-Way catalyst. For additional information, including drawings, please check out the product page. |
|
|
|
|
| 03/31/09 |
G8.3E Power Unit Released! |
|
| |
| CPP is pleased to announce the release of the G8.3e Power Unit (engine configuration D551015CX03). This power unit conforms to 2008 NSPS Standards with a factory installed AFR and includes a 3-Way catalyst. For additional information, including drawings, please check out the product page. |
|
|
|
|
|
| 03/11/09 |
FH Option Help! |
|
| |
 |
A common dilemma for engine spec.ing is FH selection. The CPP option information section of each engine home page allows you ( in most cases ) to select from a variety of FH sizes. The question then becomes, which of the FH options are acceptable? To assist in answering the question, click on any MM option and open the installation drawing PDF. A title box on the drawing will show what FH the mounting was designed for. Should you want the same SAE size but a different option ( wet vs dry, iron vs aluminum ) you only need to compare the FH's starter location, mounting pad location/dimensions and the housing's thickness to decide if the FH is an acceptable substitute. |
|
|
|
|
| 03/06/09 |
Remote Mount Panels and Throttle Extensions |
|
| |
| When ordering a control panel for an ecm controlled engine, you may take advantage of the panel's ability to be mounted remotely. We supply 12 and 24 foot extension harnesses for that purpose. 100 feet of extension harness combinations is the most allowed. The electronic "hand throttle" is also available for remote mounting. The throttle is designed to be plugged into the control panel, therefore it moves with the panel, without requiring an extension harness as well. You only need an throttle extension harness if you want to separate the throttle from the control panel. The throttle extension limit is also 100 feet. The maximum, combined extension of panel and harness is 100 feet. e.g. if you move the panel 75 feet, the throttle can only be extended an additional 25 feet. |
|
|
|
|
|
| 03/02/09 |
News for Emergency Stop Users |
|
| |
 |
CPP has a five amp fuse in the harness from the engine ecm to the CPP supplied control panel. It sits in the wire going from the ecm to the 31 pin connector, pin number one. E-stops users can access this fuse to accomplish their task, easier then cutting into the harness. A suggested diagram for wiring an e-stop, using the 5 amp fuse connection is available here. |
|
|
|
|
| 02/06/09 |
New Low Mount Air Cleaners for Enclosed Power Units |
|
| |
CPP has released new air cleaner options for enclosed QSB6.7, QSC8.3 and QSL9 power units. The rain caps on the air cleaners are completely below the enclosure top.
For more information on these new options, please follow the links below.
QSB6.7-P Tier 3
QSC/QSL Tier 3 |
|
|
|
|
|
| 01/07/09 |
Cleanfix Reversing Fan for QSK19-P T3 |
|
| |
Download the Power Point Presentation. |
Benefits
- Very effective radiator cleaning solution
- Virtually maintenance free
- Simple setup (set timer, walk away)
- Comes with all necessary equipment
- Clean radiators save fuel
- Clean radiators keep cooling efficiency maximized
For option details, click here. |
|
|
|
|
| 01/01/09 |
B3.3NA with Rear Engine Power Take-Off (REPTO) |
|
| |
CPP is pleased to announce the released PRIC 5522 in CSL for the B3.3NA, engine configuration D781008CX03. This price spec includes the REPTO flywheel housing (FH9686) and the appropriate CPP options for mounting and installing this engine configuration. For additional information, as well as drawings, please check out the product page.
 
|
 |
|
|
|
|
| 06/27/08 |
|
|
| |
|
Due to the volume of orders being received through the Cummins Distribution Network (our only customers), CPP is adding additional assembly personnel to increase our through-put and improve our Lead Times. Our goal is to better serve you, our customers. |
|
|
|
|
| 06/26/08 |
|
|
| |
The CPP team would like to thank Cummins Western Canada for their recent order for 14 QSK23-P Power Units! |
|
|
|
|
|
| 06/25/08 |
New QSK19-P Tier 2 Low Profile Power Unit
|
|
| |
Click for Larger Image
|
CPP has released a QSK19 Power Unit for use in the oil and gas industry. The unit is designed for use as a Mud Pump or Draw Works power source.
Development of this product is the result of a joint effort between Cummins Western Canada and Cummins Power Products. Randy Pehlke and Ching Gettman of Cummins Western Canada, along with Randy's Engineering Team were the Voice of the Customer for this product. Stephen Grunewald, Director of Engineering for CPP, and his team member Ryan Hanson took the information from Western Canada and made this product a reality.
- 800HP @ 2100 rpm capability
- Roda Deaco intake shutdown wired into ECM for fuel cutoff during E-Stop
- Ultra compact package for oil and gas market: 68.1” high 115.1” long and 63.75” wide
- Heavy duty steel skid made from ½” plate
- Gages visible through NEMA weatherproof control box viewing window
- Integral transmission cooler equipped
- EPA/CARB/EU certified
- 125°F Ambient temperature capable
To view a presentation with more diagrams, please click here.
|
|
|
|
|
| 05/22/08 |
QSK23-P Tier 2 Power Unit Released
|
|
| |
Cummins Power Products has released the QSK23-P Tier 2 power unit. More information about this new product offering is available here. |
 |
|
|
|
|
| 2/27/2008 |
New DC Genset Case Study Now Available |
| |
The El Paso, TX Water Utilities desalination plant uses three DCathlon gensets for supplemental power to their injection wells. Read the full case study. |
|
| 2/26/2007 |
Citizens Communications Powers Up with DC Generators! |
| |
Citizens Communications, part of the Frontier family of telecommunications companies, is the newest customer for Cummins Power Products. This particular relationship is especially rewarding as Citizens had previously purchased several of the DCathlon DC Generators when the product was assembled by Cummins Power Generation. Citizens is planning more DCathlon installations in the near future in order to enhance their system reliability . Citizens Communications is one of the nation's largest rural local exchange carriers, operating in 24 states. |
|
| |
|
| 1/10/2007 |
|
| |
Old main page stories are now being archived for you to look through later. We had several people ask us what happened to the old news, so we are starting to add these stories to a new section to make things easier to find. |
|
| 10/20/2007 |
|
| |
QSB3.3 Tier 3 Power Units Now Available!
Price spec information available here.
Additional Power Unit information available here.
|
 |
|
|
| 9/1/2007 |
|
| |
New CPP LIGHT web site!
Cummins Power Products has launched a new web site for International distributors, Domestic dealers, and end users. It is based on our standard CPP web site but has sensitive information removed, such as pricing and parts drawings, so that it can be provided to the general public.
Serial number look-up and order status are available for customers to view, however the data will be updated every 24 hours (the standard CPP site is updated continuously). As a NA Distributor or fully owned international distributor, your best source of information will continue to be our standard CPP web site however you may find the new public site useful when you are not in the office. The new site is located at CumminsPowerProducts.com |
|
| 7/1/2007 |
|
| |
Cummins Power Products has made the decision to replace all Power View 100 equipped panel options with the Teleflex model 2600 GEM ( generic engine monitor) The Gem works the same way as the PV 100 and is expected to provide better reliability. The new panel option IN 11264 / INPU 10213 replaces all the PV 100 options. It works with both 12 and 24 volts systems.
PV 100's can no longer be ordered. Barb Morrison will work with you to convert your shop orders during the short transition period.
|
|
|
